Enhanced/Balanced 3S 13.6V 60A 18650 Li-ion Battery Charge PCB Protection Module

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Enhanced/Balanced 3S 13.6V 60A 18650 Li-ion Battery Charge PCB Protection Module
Popular
Popular
Product Introduction
Descripton
Item:Battery Charger Protection Board
Model: BMS-60A-3S
Product size: 41*55*3.4mm (enhanced version), 42*62*3.4mm (balanced version)
Charging voltage: 12.6V - 13.6V
Type:enhanced version,balanced version
Scope of application: Suitable for lithium batteries with nominal voltage of 3.7V and full voltage of 4.2V (including 18650, 26650, polymer lithium batteries, no size limit).
Continuous discharge current (upper limit): 60A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current (upper limit): 15A
Enhanced version version: Suitable for electric drills with a starting current of 120A or less and a power of 260W or less.
Balance version: Suitable for electric drills with starting current below 120A and power below 260W, with balanced charging function.
Note 1: Successfully start the drill requires 3 15C-20C power batteries, or 6 10C-15C power batteries (recommended power battery models:  VTC4, VTC4A, VTC5A, VTC6); 0V and 12.6V cable, Use copper wire above 4 mm2 (cannot use nickel plate! ! !).
Note 2: Strictly follow the wiring of the diagram 0V, 4.2V, 8.4V, 12.6V, do not intentionally short circuit.
Note 3: When charging the battery, the "430" resistance heating is normal, indicating that the equalization circuit is working; if the "430" resistor is also hot in the uncharged state, please check if the wrong line is connected.
For some customers with poor electronic foundation, please explain: Do not mix good battery and poor battery! The closer the capacity/internal resistance of the 3 batteries is, the better! (The effect of 2 good batteries + 1 poor battery) = 3 use of poor battery).
Package:
1 x 3S 60A Battery Charger Module ( Enhanced / Balanced )
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Enhanced/Balanced 3S 13.6V 60A 18650 Li-ion Battery Charge PCB Protection Module
Product Introduction
Descripton
Item:Battery Charger Protection Board
Model: BMS-60A-3S
Product size: 41*55*3.4mm (enhanced version), 42*62*3.4mm (balanced version)
Charging voltage: 12.6V - 13.6V
Type:enhanced version,balanced version
Scope of application: Suitable for lithium batteries with nominal voltage of 3.7V and full voltage of 4.2V (including 18650, 26650, polymer lithium batteries, no size limit).
Continuous discharge current (upper limit): 60A (If the heat dissipation environment is not good, please reduce the load current)
Continuous charging current (upper limit): 15A
Enhanced version version: Suitable for electric drills with a starting current of 120A or less and a power of 260W or less.
Balance version: Suitable for electric drills with starting current below 120A and power below 260W, with balanced charging function.
Note 1: Successfully start the drill requires 3 15C-20C power batteries, or 6 10C-15C power batteries (recommended power battery models:  VTC4, VTC4A, VTC5A, VTC6); 0V and 12.6V cable, Use copper wire above 4 mm2 (cannot use nickel plate! ! !).
Note 2: Strictly follow the wiring of the diagram 0V, 4.2V, 8.4V, 12.6V, do not intentionally short circuit.
Note 3: When charging the battery, the "430" resistance heating is normal, indicating that the equalization circuit is working; if the "430" resistor is also hot in the uncharged state, please check if the wrong line is connected.
For some customers with poor electronic foundation, please explain: Do not mix good battery and poor battery! The closer the capacity/internal resistance of the 3 batteries is, the better! (The effect of 2 good batteries + 1 poor battery) = 3 use of poor battery).
Package:
1 x 3S 60A Battery Charger Module ( Enhanced / Balanced )
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.